Vibration Analysis and Optimization of Spur Gear Used in EOT Crane Machine

Yogesh P. Chaudhari, Dr. D. Y. Patil School of Engineering, Lohegaon,Pune-412105; Swapnil S.Kulkarni ,Able Technologies India Pvt. Ltd., Pune; Prof. Amol B.Gaikwad ,

Mass, Vibration, Material, EN32A, EN24, EN202, Modal Analysis

A gear is a rotating machine part having cut tooth, which mesh with another toothed part in order to transmit torque. To design the spur gear to study the weight reduction and stress distribution for cast steel and composite materials. Gearing is one of the most critical components in a mechanical power transmission system, and in most industrial rotating machinery. The main objective of this research work is to introduce a new gear material for gear. EN32A, EN24 is selected for suitability analysis. Gears are the important part of any machine application like electric overhead travel, machine tool, automobile for power transmission. The main part of this research work is to identify the natural frequency and natural vibration modes of EN32A, EN24 gear and also the effect of change in mass of gear. This project is based on the topology optimization of the existing gear with the reduction of material from the gear and to reduce the total weight of the gear. F.E. Modelling shall be pursued for deriving analytical solution to the problem while physical experimentation would be done to offer inputs to the work and validate the model at the initial phase of work. Hyper Works is being considered as a CAE tool for Pre-processing, Solving and Post processing. The experiment would be performed on the physical setup for the existing/ benchmark case.
    [1] Amit Aherwar, Md. Saifullah Khalid. “Vibration Analysis Techniques For Gearbox Diagnostic: An International Journal Of Advanced Engineering Technology” E-Issn 0976-3945. [2] Jianming Yang, “Vibration Analysis On Multi-Mesh Gear-Trains Under Combined Deterministic And Random Excitations”, Mechanism And Machine Theory 59 (2013) 20–33. [3] Zhonghong Bu, Geng Liu , Liyan Wu, “Modal Analyses Of Herringbone Planetary Gear Train With Journal Bearings” , Mechanism And Machine Theory 54 (2012) 99–115. [4] Marianne Mosher, Anna H. Pryor, David G. Lewicki, “Detailed Vibration Analysis Of Pinion Gear With Time-Frequency Methods”, Nasa/Tm-2003-212269. [5] Alexander Kapelevich Graco, “Geometry And Design Of Involute Spur Gears With Asymmetric Teeth”, Mechanism And Machine Theory 35(2000) 117–130. [6] Mitchell Lebold, Katherine Mcclintic, Robert Campbell, Carl Byington, And Kenneth Maynard, “Review Of Vibration Analysis Methods For Gearbox Diagnostics And Prognostics”, Proceeding Of The 54th Meeting Of Society For Machinery Failure Prevention Technology, Virginia Beach, Va,May 1-4,2000,P.623-634. [7] G.Dalipaz, A.Rivola and R.Rubini, “Gear Fault Monitoring: Comparison Of Vibration Analysis Techniques”, 2-I-40136 Bologna, Italy. [8] Jiri Tuma, “Gearbox Noise and Vibration Prediction and Control”, International Journal Of Acoustic And Vibration, Vol.14, No.2, 2009. [9] Abhilesh Warade, “Vibration Analysis Of Annular Disc With Periodic Uniform Radial Slots While Disc Is Clamped At Inner Edge And Free At Outer Edge” E-Issn 0976-3945. [10] Mr. K.S. Tanpure, “Vibrational Analysis Of Genset Silencer Using Fea & Fft Analyzer”. Issn: 2349-6193. [11] Mr. Ashwani Kumar, Himanshu Jaiswal, Rajat Jain, Pravin Patil “Free Vibration and Material Mechanical Properties Influence Based Frequency And Mode Shape Analysis Of Transmission Gearbox Casing”. Procedia Engineering 97(2014) 1097-1106. [12] Mr. Ashwani Kumar, Arpit Dwivedi, Vipul Paliwal, Rajat Jain, Pravin Patil “Free Vibration Analysis Of Al 2024 Wind Turbine Blade Designed For Uttarakhand Region Based On Fea”. Procedia Technology 147(2014) 336-347. [13] M. A. Chowdhury, Md. M. Helali: The Influence of Natural Frequency Of The Experimental Set-Up On The Friction Coefficient Of Stainless Steel-304. Tribology In Industry Vol 32, Pp.19-24 (2010).
Paper ID: GRDJEV01I090020
Published in: Volume : 1, Issue : 9
Publication Date: 2016-09-01
Page(s): 5 - 13